1

Start with the fairlead nodes

A floating model starts with the points where the mooring lines attach to the hull: the fairleads. The starter has three, 120° apart on a 5 m sphere, 2 m below MSL, plus gravity.

  1. Click Offshore › Workflows (F1), open Offshore structures and choose Moored floating body.
  2. Click Load the fairlead nodes.

For your own hull, add nodes with Node… at the fairlead positions (and at the tower base for a floating turbine).

The finished model is File › Samples › Moored floating sphere. File › Samples › OC4 DeepCwind semi-submersible shows a floating wind turbine.

2

Create the offshore environment

Use the water density of the hydrodynamic data: 1000 kg/m³ for the bundled sphere.

  1. Click Offshore › Environment and enter:
FieldValue
Design codeISO 19902
Water depth60 m
MSL elevation0 m
Water density1000 kg/m³
3

Define the waves

Small regular waves show the motion of the hull clearly. For a real design, also add an irregular sea.

  1. Click Offshore › Design wave and enter:
FieldValue
Wave theoryAiry (linear)
H / T2 m / 6 s
Heading0°
4

Add the three mooring lines

Each line runs from one fairlead to an anchor on the seabed and is laid out on its static catenary. The direction points away from the hull by default.

  1. Click Select fairlead 1 in the workflow step.
  2. Click Offshore › Floating › Mooring line and enter the values below.
  3. Repeat for fairleads 2 and 3.
FieldValue
Line typestudless chain, R3
Nominal diameter0.06 m
Anchor distance105.5 m
Line length128 m
Segments32

The Output panel shows each line's static fairlead tension and how much of it lies on the seabed. If the Output says a line is taut, it is shorter than the anchor distance: undo (Ctrl+Z) and enter a longer line.

5

Add the floating hull

The hull is a rigid body. Its hydrostatics, radiation damping, added mass and wave excitation come from a BEM file (.h5, from Capytaine, WAMIT or NEMOH). The default values are those of the bundled sphere.

  1. Click Select all fairleads in the workflow step, so the lines attach to the hull.
  2. Click Offshore › Floating › Floating body (rigid hull)… and check the values:
FieldValue
Hydrodynamic databuiltin:sphere.h5
Mass261.8 t
CoG0, 0, −2 m
Ixx = Iyy = Izz2.6 × 10⁶ kg·m²
DisplaySphere, radius 5 m

Use the equilibrium of the BEM data

The CoG must be the equilibrium position of the BEM data. Otherwise the hull starts away from equilibrium and drifts.

6

Check the mesh

Show mesh draws the chain elements. Solving rebuilds the mesh whenever the lines change.

7

Find the static pretension (optional)

A Nonlinear study holds the hull in place and finds the static shape of the chains under their weight.

  1. Click Analysis › Nonlinear static.
  2. Click Member forces. The chain tension is highest at the fairleads. Compare it with the catenary tension in the Output.
8

Run the hull in waves

A Dynamic study couples the hull hydrodynamics to the flexible chains, including contact with the seabed.

  1. Click Run waves (Dynamic, 60 s) in the workflow step. It creates “Waves 60 s” (first sea state, 60 s, 0.02 s steps) and runs it.

Floating runs use implicit Euler time stepping. If a run fails with slack and taut chains, shorten the time step in the study's Properties.

9

Review motions and line tensions

  1. Animate plays the run: the sea surface, the hull and the chains move together.
  2. In the Chart, choose Offshore to plot the heave, surge and pitch of the hull and the fairlead tensions over time.
[SCREENSHOT] Chart › Offshore: fairlead tensions of the three chains over 60 s
10

Create the report and save

File › Report includes the fairlead tensions (maximum and final) of every mooring line. Save it as a web page, or print it to PDF, and save the project with Ctrl+S.

What you learned

  • Mooring lines start at a selected fairlead and are laid out on their catenary.
  • A floating hull is a rigid body with BEM data; the selected nodes are attached to it.
  • Nonlinear static gives the pretension with the hull held; Dynamic gives motions and tensions in waves.